בניית אתרים בחינם


The Simplest Way to Change The Tire of any Mountain Bike
Whether you are a regular bike rider or get a chance to ride it once in a while, you might have come across a state of affairs to mend few parts of your bike. Riding a mountain bike often means that one or both of the tires might have gone flat. There might be no one around to assist you out of such a state, so repairing flat bike tires is a essential thing you need to know. Sometimes your bike's tire is damaged internally, so you have to repair the inner tube to make things right.
Here are few steps you need to follow to change/ repair the tire of your mountain bike. Keep reading…
Bicycle Spokes Suppliers 

1. Set the bike upside down
The first thing you need to do if you want to repair your bike's out of order tire is to position your bike on to its handle. The tires will come on top from where it would be easy to take away & repair the tires. Place it adequately on a flat surface so that it should not shake while repairing.

2. Remove the faulty tire
Next thing you need to do is loose the nuts on the axle which holds up the tire. Other various things like gear levers, brake wires depends upon your bike's manufactured structure, so loose up the tire entirely so that you can take it out of the framecasing or axle.

3. Remove the tube from the rim
After you have removed the tire from the axle, open up the tire using iron rods which can be easily put in between tire & rim without damaging the tube inside. do again the action of putting iron rods between tire & rim unless tire comes off the rim. Find the input point of air on the tube & force down it to take off the tube from the rim. 

4. Check the inside of the tire for faults
Once you have removed the tube as well from the tire, put a cloth inside the empty tire & clean it from the inside. After you have done the cleaning, check for any damages inside the tire or something that damaged the tube, like nails, pointy items stuffed in the tire etc. 

5. Look for faults in the tube
The tube must be pumped in with air & should be checked intelligently for any faults. Even then if you are unable to find the out of order area, fill a big container of water to submerge the air filled tube in it to see from where the air is ooze out. In case the error is along the ridge, then the tube is severe; you will have to buy a new tube in its place.
6. Patch up the holes/faults
After you have located the faults or holes in the tube, patch it up using repair equipment. uneven up the area around the fault using rub down so that the patch is easily fixed there. Use a steamy patch to wrap the fault and stick it over to totally close up the area, such that air cannot run away it after it gets arid.

7. Test the patched up tube
The patching of the fault needs some time to clear up down or dry out. After it is dry, pump up the tube with air to make sure whether the patch is functioning or not by submerging it under water or by placing it close to your ear to check for any air escape.

8. Set tube on rim & set the tire
After completely testing the tube & tire, place tube on the rim like it was earlier than and place tire on top of the tube. With the help of iron rods, put the tire back into the rim with utmost care without damaging the tube. Check thoroughly the tire so that it must be totally enclosed within the rim.

9. Pump up the tire
After fitting the tire on the rim, place it on the axle & fasten the gear levers, brake wires etc back to the tire and make sure to tighten the bolts attached to the tire. Pump the air into the tube and you are ready to go.

on the whole, you need to be a little bit dutiful while opening up the tire to repair it as it should be later. Also, you should make sure for more than 1 fault if there are any so that your time is saved by completely setting up the whole thing at once. With time, you will feel it simple to change or repair the faulty tire, saving your money of going to an specialist; you yourself will be one.

my2all.com - Website Building - my2all.com - WebSite Building